How to control aux heater?: Unterschied zwischen den Versionen

Aus I-BUS App Wiki
Wechseln zu: Navigation, Suche
K
K (Control by I-BUS app)
Zeile 8: Zeile 8:
 
== Control by I-BUS app ==
 
== Control by I-BUS app ==
 
<br />
 
<br />
Wenn sicher gestellt ist, dass die STH vorhanden und mit dem Original-Radio/Navi ansteuerbar war, kann die Option "Standheizung" in den weiteren Einstellungen der I-BUS App aktiviert werden.<br />
+
If it is ensured that the aux heater was installed and can be controlled with the original radio/navi, the "Parking heater" option can be activated in the other settings of the I-BUS app.<br />
=== Steuerung mit ehemals Navigations-System ab Werk ===
+
=== Control with former navigation system ex works ===
 
<br />
 
<br />
Stelle sicher, dass die Option "MID Abfragen emulieren" '''NICHT''' aktiviert und die Option "Standheizung" aktiviert ist.<br />
+
Make sure that the option "emulate MID requests" is '''NOT''' activated and the option "aux heating" is activated.<br />
 
<br />
 
<br />
Es erscheint danach auf dem Reiter "Control" und dem Eintrag "Standlüftung" auch der Eintrag "Standheizung". Über den Slider daneben kann die STH (oder STL) direkt gestartet werden.<br />
+
The " auxiliary heating" entry then also appears on the "Control" tab and the " auxiliary ventilation" entry. Both can be started directly via the slider next to it.<br />
Darüber befinden sich zwei Timer, für die eine Startzeit gestellt werden kann.<br />
+
Above are two timers for which a start time can be set.<br />
Ist der Timer erfolgreich gestellt, so kann man im Tacho mit großem Textdisplay (sofern die PROG-Funktion "ZEIT1" und "ZEIT2" aktiv sind) die entsprechende Startzeit aufrufen, welche mit einem Stern markiert ist.<br />
+
If the timer is set successfully, you can call up the respective start time in the speedometer with large text display (provided the PROG function "TIME1" and "TIME2" are active), which is marked with an star.<br />
Der Timer ist damit erfolgreich gesetzt. Den Start der STH übernimmt das Kombi-Instrument zur eingestellten Zeit.<br />
+
The timer is now successfully set. The speedometer takes over the start of the aux heater/ventilation at the set time.<br />
 
<gallery mode="packed-hover">
 
<gallery mode="packed-hover">
Low BC calc-MID Emulation.png|Richtige Einstellung für Low BC Berechnung und MID Emulation
+
Low BC calc-MID Emulation.png|Correct setting for Low BC calculation and MID emulation
00_IBUS-App_Control.png|Startseite Control
+
00_IBUS-App_Control.png|Page "Control"
9_IBUS-App_Ansteuern1.png|Zeiteinstellung Standheizung/-lüftung
+
9_IBUS-App_Ansteuern1.png|Time setting auxiliary heating/ventilation
 
</gallery><br />
 
</gallery><br />
 
<br />
 
<br />
  
=== Steuerung mit ehemals nur Radio ab Werk ===
+
=== Control with former radio only ex works ===
 
<br />
 
<br />
Stelle sicher, dass die Option "MID Abfragen emulieren" und die Option "Standheizung" aktiviert sind.<br />
+
Make sure that the option "emulate MID requests" and the option "auxiliary heating" are activated.<br />
 
<br />
 
<br />
Auf dem Reiter "Control" erscheint nun ein großer Button "MID". Nach dem dieser betätigt wird erscheint ein emuliertes MID, so wie es zuvor bekannt war. Unter "Clock" erreicht man das Menü zum setzen der "ZEIT1" oder "ZEIT2". Nach erfolgreich gesetzter Startzeit wird vor "Zeit1"/"ZEIT2" ein Stern gesetzt.
+
On the "Control" page, a large "MID" button appears. After pressing this button, an emulated MID appears, as it was known before. Click on "Clock" to access the menu for setting "TIMER1" or "TIMER2". After the start time has been successfully set, a star is placed in front of "TIMER1"/"TIMER2".
 
<gallery mode="packed-hover">
 
<gallery mode="packed-hover">
00_IBUS-App_Control_MID_08.png|Umstellung auf "MID Emulation aktiv" (wenn zuvor MID verbaut war!)
+
00_IBUS-App_Control_MID_08.png|Switch to "MID emulation active" (if MID was previously installed!)
Low BC calc-MID Emulation.png|Richtige Einstellung für Low BC Berechnung und MID Emulation
+
Low BC calc-MID Emulation.png|Correct setting for Low BC calculation and MID emulation
00 IBUS-App Control MID.png|MID Start-Button
+
00 IBUS-App Control MID.png|MID start button
00_IBUS-App_Control_MID_01.png|Start-Seite MID Control
+
00_IBUS-App_Control_MID_01.png|MID control
 
00_IBUS-App_Control_MID_02.png|MID - Clock
 
00_IBUS-App_Control_MID_02.png|MID - Clock
00_IBUS-App_Control_MID_03.png|MID - Zeit 1 und 2
+
00_IBUS-App_Control_MID_03.png|MID - Tim,er 1 and 2
00_IBUS-App_Control_MID_05.png|MID - Zeit 1 stellen
+
00_IBUS-App_Control_MID_05.png|MID - set TIMER 1
 
</gallery><br />
 
</gallery><br />
  

Version vom 7. Dezember 2022, 07:32 Uhr


- side under construction -

Check German Version: Wie kann ich die Standheizung steuern?

Control by I-BUS app


If it is ensured that the aux heater was installed and can be controlled with the original radio/navi, the "Parking heater" option can be activated in the other settings of the I-BUS app.

Control with former navigation system ex works


Make sure that the option "emulate MID requests" is NOT activated and the option "aux heating" is activated.

The " auxiliary heating" entry then also appears on the "Control" tab and the " auxiliary ventilation" entry. Both can be started directly via the slider next to it.
Above are two timers for which a start time can be set.
If the timer is set successfully, you can call up the respective start time in the speedometer with large text display (provided the PROG function "TIME1" and "TIME2" are active), which is marked with an star.
The timer is now successfully set. The speedometer takes over the start of the aux heater/ventilation at the set time.



Control with former radio only ex works


Make sure that the option "emulate MID requests" and the option "auxiliary heating" are activated.

On the "Control" page, a large "MID" button appears. After pressing this button, an emulated MID appears, as it was known before. Click on "Clock" to access the menu for setting "TIMER1" or "TIMER2". After the start time has been successfully set, a star is placed in front of "TIMER1"/"TIMER2".


Control by orange Resler Module


NOTE: If the function is set to auxiliary heating on vehicles WITHOUT auxiliary heating and this is started, malfunctions will occur. Often the fan is started and cannot be stopped unless the vehicle battery is disconnected. Therefore make sure that a auxiliary heating is installed.
An indication of an installed auxiliary heater can(!) be a sticker of the manufacturer "Webasto" in the engine compartment on the left dome. However this is also present if only one auxiliary heater is coded on diesel vehicles.

The Resler module can perform the control of the auxiliary heating/ventilation.
Initially the type must be defined (especially for control via remote control).

OFF There is NO control of the auxiliary heating/ventilation.
type 1 Only for E38/E39/E53 with high BC speeedometer
type 2 E38/E39/E53 with Low BC speeedometer
relay In the E46/E83/E85 the auxiliary heating is controlled via +12V switching signal instead of via the BUS system.

With retrofitting a relay (not included) a relay may be switched via ground signal on the green wire from the Resler module.
IMPORTANT! A 12V relay with more than 250 Ohm excitation winding and recovery diode is required! Otherwise the Resler Module may be destroyed.

To decide which type to set, please check: Habe ich High oder Low BC?

Direct start of the auxiliary heating/ventilation via remote control

The remote control in the vehicle key can be used to start/stop the auxiliary heating/ventilation directly.
Use the slider to determine whether the auxiliary heating or auxiliary ventilation is to be used.

Starting auxiliary heating/ventilation The vehicle has to be locked. Press and hold the close button on the key for approximately 2 seconds. The start is confirmed visually by 2x "slow flashing".
Stop auxiliary heating/ventilation The vehicle has to be locked and the auxiliary heating/ventilation has to be running. Press and hold the close button on the key for approx. 2 seconds. The stop is confirmed visually by 3x "slow flashing". Note: The auxiliary heating cools down with the combustion air fan for approx. 180s so that it does not stop immediately.



Timer control for auxiliary heating/ventilation

The Resler Module allows pre-programming of up to 8 timers with a lead time of up to one week and weekly repetition beyond that.

Example Example
activate/ deactivate timer Set the slider accordingly. After the timer has run, it is deactivated.
Start time Set the start time for the timer
Duration Setting the duration of the timer (1-30 minutes)
Days Set the days on which the timer should be active
Weekly repetition The complete timer is repeated continuously every week as it is set.

The option also has to be set if the timer shall run on more than one day. Otherwise the timer will be deactivated after the first run.

Functional type The type can be set to auxiliary heating/ventilation or relay.

The air-conditioning control unit decides whether ventilation or heating is required based on the outside temperature (16°C is the switchover point).

NOTE: Since the air conditioning control unit decides which function is to be implemented the timer can usually always be used for the auxiliary ventilation function (except E46/E83/E85) even if no auxiliary heating is installed.



Standheizung im E46/E83 oder Standheizung ohne BUS Steuerung


Standheizungen, die nicht über den Fahrzeug-BUS sondern über nur ein 12V Schaltsignal gesteuert werden, können nicht über die I-BUS App gesteuert werden.
Es gibt jedoch die Option hierfür den Masse-Schaltausgang (grüne Litze) sowie eine geeignete Relaisschaltung (Miniaturrelais plus Freilaufdiode!!!!) zu nutzen und das Modul entsprechend einzustellen.
Es ist absolut essentiell hier nur ein kleines Relais (kein Kfz Relais! - max. 100mA Last!!!) mit Freilauf-Diode zu nutzen um damit den Massekontakt am Relais zu schalten. Die Versorgung mit Dauerplus am Relais und zum Durchschalten auf die STH muss separat organisiert und abgesichert werden! Wird dies nicht beachtet kann das Modul beschädigt irreparabel werden!

Einstellung für Direktstart via FFB muss auf "Relais" gesetzt werden:

Relais Bei E46/E83/E85 erfolgt die Ansteuerung der Standheizung via +12V Schaltsignal statt über das BUS System.

Mit Nachrüstung eines Relais (nicht enthalten) kann ein Relais via Massesignal an der grünen Litze vom Resler Modul geschaltet werden.
WICHTIG! Es wird ein 12V Relais mit mehr als 250 Ohm Erregerwicklung und Freilaufdiode benötigt! Anderenfalls kann das Modul zerstört werden.



Wird der Timer genutzt, so muss der Funktionstyp ebenso auf "Relais" gesetzt werden:

Funktionstyp Der Typ kann auf Standheizung/-lüftung oder Relais gesetzt werden.

Ob gelüftet oder geheizt wird entscheidet das Klimabedienteil anhand der Außentemperatur (16°C ist der Umschaltpuntk).



Diese Umsetzung ist bislang nur experimentell erfolgt. Tretet bei Rückfragen gern VOR der Umsetzung mit uns in Kontakt!

Voraussetzungen für die Ansteuerung der Standheizung


Die Voraussetzung für die Nutzung der Standheizung ist natürlich, dass eine Standheizung im Wagen verbaut ist, welche über das BUS System des Fahrzeuges gesteuert wird.
Das ist bei allen BMW E38/E39/E53 mit Standheizung ab Werk der Fall.
Dazu haben alle Dieselmotoren (M47/M57) einen sogenannten "Zuheizer", der baugleich mit der Standheizung ist. Es fehlt nur die passende Codierung und eigentlich ein Umschaltventil (wo mit NUR der Motor geheizt wird).
Standheizung ab Werk heizt also nur den Kühlkreislauf für die Fahrgastzelle - nicht den Motor.
Ein zur Standheizung codierter Zuheizer (oder eine Standheizung mit abgestecktem Umschaltventil) heizt den kleinen Kühlkreislauf und erwärmt somit Motor und die Fahrgastzelle.
Dazu findet man auch im Motorraum auf dem rechten Dom einen weißen Sticker der Firma "Webasto". Dieser besagt erstmal nur, dass eine Webasto Thermotop C/Z verbaut ist. Nicht aber, ob es eine Standheizung oder nur ein Zuheizer ist.

Der Einfachheit halber werden wir "Standheizung" mit "STH" und "Standlüftung" mit "STL" abkürzen.

HINWEIS: wird bei Fahrzeugen OHNE Standheizung die Funktion auf Standheizung gesetzt und diese gestartet, so kommt es zu Fehlfunktionen. Oft wird das Gebläse gestartet und kann nur durch Abklemmen der Fahrzeugbatterie gestoppt werden!!! Stellen Sie daher sicher ob eine Standheizung verbaut ist.
Ein Indiz auf eine verbaute Standheizung kann(!) einen Aufkleber der Firma "Webasto" im Motorraum auf dem Dom links sein. Allerdings ist dieser auch vorhanden, wenn bei Dieselfahrzeugen nur ein Zuheizer codiert ist.

Steuerung ab Werk


Um sicher zu sein, dass das "Webasto-Gerät" auch als Standheizung funktioniert kann man z.B. im Original-Menü vom MID oder Bordmonitor nachsehen.
Hier sollte man neben der "Standlüftung" (welche mit elektronischem Klimabedienteil immer verfügbar ist) auch "Standheizung" aufgeführt und ansteuerbar sein.
Im MID findet man dazu die Option "HEIZ EIN" und "LÜFT EIN", nachdem man auf das Uhr Icon gedrückt hat. Sollte hier nur die Standlüftung aufgeführt sein, so wird es zu Fehlfunktionen kommen, wenn man versucht die STH via App/Modul anzusteuern!!!
Daher bitte unbedingt vorher sicherstellen, dass die STH auch als solche codiert ist!

Timer: Standheizen oder -lüften?


Die Entscheidung ob beim Erreichen des Timers geheizt oder gelüftet wird trifft das Klimabedienteil auf Basis der Außentemperatur.
Hierzu ist es essentiell, dass der Sensor intakt ist und plausible Werte im Tacho gezeigt werden. Bei defektem Sensor wird im Tacho permanent "-40°C" gezeigt, entsprechend startet IMMER die STH, egal welche Außentemperatur tatsächlich anliegt.

Abbruchkriterien


Die STH wird abgeschaltet, wenn:

  • die Kühlmitteltemperatur 70°C übersteigt
  • die Spannung unter 10V fällt
  • der Tankinhalt unter 7l fällt
  • die Laufzeit 30min erreicht hat
  • ein Defekt der Standheizung vorliegt