Resler Module Configurator: Unterschied zwischen den Versionen

Aktuelle Version vom 21. Juli 2022, 07:02 Uhr

With the Resler Module Configurator (current version: 0.9.29) you may comfortably configure all functions of the Resler Module on your desk at the computer prior to installing the module into the car.
The configurator is particularly convenient to use thanks to its appealing user interface. It is primarily used for settings when the Resler Module is to be used standalone (i.e. without the Android radio/I-BUS app).

• Read / write Resler Module
• Flash Resler Module firmware from a file (available updates are recognised and automatically downloaded from the Internet).
• load and save Resler Module configuration (from/to file)
• Load and save CHLH light sequences from file (also in I-BUS App format to transfer them to the module with the I-BUS App in the car).
• Set vehicle configuration
• Configure CHLH Start and Stop
• Configure auxiliary heating / auxiliary ventilation
• Configure folding/unfolding mirrors
• Configure timer for auxiliary heating / auxiliary ventilation / relay output
• configure comfort blinking / cornering light / daytime running light / highway light
• Conveniently create / edit light sequences
  

Especially the editing of CHLH light sequences is much more easy with the configurator on the PC than in the car.


The following settings are available in the Resler Module Configurator:

Load/Save

• 

  Resler Module Configurator

• 

  Resler Module Configurator

• 

  Resler Module Configurator

• 

  Resler Module Configurator

Module

With "Read module", the configuration on the module is read out and displayed in the Resler module configurator. It can then be edited.
With "Write module" the configuration set in the Resler Module configurator is written to the Resler Module.

Firmware

With "Flash Firmware File" you can flash a previously downloaded firmware onto the Resler Module.
If the firmware on the module is not up to date an info appears and the button "Flash firmware update" is displayed and can be confirmed.
The progress of the flash process is shown in the bar next to it.
If a module is connected the firmware version of the module will be displayed at the bottom of the field.

Module Configurator

Here you can save the created configuration on the computer or load a configuration saved on the computer to display it in the Resler Module configurator, edit it or write it to the module.
Configurations have the file format *.rmc

I-BUS App

Light sequences can be loaded into the file format of the I-BUS App (*.xml) to be shown or edited under "Light sequences". For this purpose light sequences can be saved again in the file format for the I-BUS App. These can then be transferred to the Android device with a data carrier (USB stick or SD card) and imported in the app in the lighting control under "Load".

Language

Currently the Resler Module Configurator is available in German and English.
Other languages are in the process of being added.
If you are fluent in a language other than German or English - and know all the technical terms used in the app - and want to help Rolf translate the app: [get in touch with Rolf]!

Module Mode

You have to specify whether the module is to be

• in operation with or without I-BUS app
• "Module active" (all functions active)
• "Module only active with ignition off" (only CHLH, mirror flaps and aux heater control works).
• "Module completely inactive"

In particular BMW E46/E83/E85 (i.e. with LSZ) have to REMOVE the hook at "Operation with I-BUS App" in the mode if the module is to be used without I-BUS App. Otherwise, the speedometer will dim when flashing.

Car configuration

• 

  Resler Module Configurator

Car series

Select the series of the vehicle in which the Resler module is to be used.
If this is not done malfunctions (such as different active lights) may occur.

On-board computer

Here you have to set whether you have installed the speedometer without on-board computer, with the small display or the large display. This applies to BMW E38/E39/E53. BMW E46 and E83 always have the "High BC".
Habe ich High oder Low BC?

Heating/ventilator

NOTE: If the function is set to auxiliary heating on vehicles WITHOUT auxiliary heating and this is started a malfunctions will occur. Often the fan is started and can only be stopped by disconnecting the vehicle battery. Therefore make sure that a parking heater is installed.
An indication of an installed auxiliary heater may(!) be a sticker of the company "Webasto" in the engine compartment on the left dome. However this is also present if only an additional heater is coded in the case of diesel vehicles.
Initially the type must be defined for this (especially for control via remote control).

Mirrors

• Fold/Unfold Mirrors: Sets the start conditions for the folding/unfolding of the mirrors. The following options are available:
  • OFF
  • Double-tapping the remote control
  • Always active
• Invert mirror unfolding: If the mirrors fold in when unlocking, the function can be reversed here
• Unfolding the mirrors when the ignition is switched on: Unfolding of the (folded) mirrors only happens when ignition level 2 is switched on.
  
  

Coming/Leaving Home

• 

  Settings for Coming/Leaving Home

Here you find the following functions:

We shorten both functions with "CHLH".

Starting time for CHLH

CHLH may be always on oder always off .
or
set start and end manually. Only if so underneath following items are shown:

or
Automatically calculate the start/end time based on location, date and twilight type:

¹unless "always active" or a "time of day calculation mode" is set
² Calculation options see table, calculated time incl. displacement is displayed in the status

• 

  twilight calculation

• 

  comparison of twilight types

Additional start/stop signals for CHLH

In addition the following start/stop signals for CHLH can be defined:

These functions are partly locked against each other so that they are mutually exclusive.

• 

  start signal CHLH

Light sequences for Coming Home/Leaving Home

The Resler Module has a microcontroller and a clock module so that it is possible to create light sequences for CHLH as desired.
A total of up to 100 sequences are possible, which can be divided between CH and LH as desired. Setting the light sequence is done as already known via the menu light control

• 

  Light selection

• 

  Load light sequence

• 

  import light sequence

• 

  save light sequence

• 

  export light sequence

• 

  example for light sequence

Quick guide:
After creating/loading/importing the light sequence:

1. Tap on „Save“
2. e.g. select memory slot 2 - 6 (memory slot 1 is intended in the app for "2x headlight flasher, not for CHLH).
3. Confirm question for use as Coming/Leaving Home
4. Select use for Coming OR Leaving Home
5. Confirm "Send to Resler Module"
6. Wait for successful writing to the Resler module, if an error occurs, restart at 1).
   
   

Download and insert sample light sequences for Coming Home/Leaving Home

In Load', there is now also the Import from the Resler module or from the memory of the radio (e.g. with sequences created on the PC or example sequences).

Timer

• 

  Resler Module Configurator

The Resler Module allows pre-programming of up to 8 timers with a lead time of up to one week and weekly repetition beyond that.

NOTE: Since the air conditioning control unit decides which function is to be implemented the timer can usually always be used for the auxiliary ventilation function (except E46/E83/E85) even if no auxiliary heating is installed.

Light functions

• 

  Resler Module Configurator

If the module is used WITHOUT Android radio and I-BUS app the settings that are set here are active in any case.
If the Resler module is used with the I-BUS app it is possible to switch in I-BUS app whether the light functions are to be performed by the Resler Module or I-BUS app.
The benefit of control via the Resler Module is that it is independent of the I-BUS App and the radio. This means that the functions are available even when the radio is switched off or the I-BUS app is closed.
To "switch off" the daytime running lights just deselect all lights.

Light sequences

• 

  Resler Module Configurator

Light sequences can be created and edited here.
It is important to specify whether the sequence is to be used for Coming Home or Leaving Home. To switch tap the respective radio button.
Lights can be selected or deselected by clicking on the respective light on the vehicle. Optionally the checkboxes can be set at the top of the text.
With the "plus" with arrow left or right a new sequence can be inserted before or after the selected sequence. The "x" deletes the selected sequence.
The duration of the individual sequences can be defined for each selected sequence via the slider or the input field.
In addition the familiar key combinations "CTRL+C", "CTRL+X" and "CTRL+V" work.

When the light sequences are ready they can be written to the module in the "Load/Save" tab via "Write module"..

Download

Download Resler Module Configurator


Quelle: www.reslers.de

Windows driver for the Resler Module

Download driver (zip)

Download driver setup

Example light sequences for download

Download sample light sequences (incl. example videos)